熊晓莉，庞瑞

（河南工业大学土木建筑学院， 郑州 450001）

 

［摘要］H型钢剖分T型钢压杆在压力作用下，屈曲性能有如下特点：一是当沿形心纵轴受压而绕对称轴屈曲时杆件将发生弯扭变形；二是当沿剪切中心轴受压而绕对称轴屈曲时弯曲变形与扭转变形不再耦合。因此，形心受压时的屈曲荷载低于剪切中心受压时的屈曲荷载，上述结论对理想压杆是适用的。然而，对于工程中具有初弯曲、初偏心以及残余应力的剖分T型钢压杆而言，将压力由形心轴移至剪切中心轴后，整体失稳时的承载能力会降低，采用有限元建模计算剖分T型钢压杆承载力的分析结果也可证实上述结论。

［关键词］剖分T型钢； 整体失稳； 弯扭屈曲； 弯曲屈曲； 有限元

中图分类号：TU318，TU3l12文献标识码：A文章编号：1002-848X(2013)13-0058-05

 

Xiong Xiaoli, Pang Rui

 (Civil Engineering and Architecture Department, Henan University of Technology, Zhengzhou 450001, China)

 

Abstract: Cut-T section obtained by splitting hot-rolled H section into two halves, has two features when buckles flexural-torsionally about axis of symmetry subject to centroid compression. On the other hand, when the force is applied at the shear center of the section, T-struts buckle either flexurally or torsionally without coupling of flexure with twisting. The buckling load of shear center loading is greater than that of centroid loading in elastic stage, which is suitable for ideal struts. However, for T-struts with defect such as fabrication error, load eccentricity and residual stress, the load capacity of overall instability decreases when moving the compression force from the centroid axis to the shear center axis. That peculiarity is verified by the nonlinear buckling analysis of load capacity of T-struts models by using ANSYS software.

Keywords: Cut-T section; overall instability; flexural-torsional buckling; flexural buckling; finite element

*“十二五”农村领域国家科技计划资助项目（2011BAD03B00），郑州市科技发展计划资助项目（2010GYXM4900），河南工业大学高层次人才基金项目（2009BS046）。

作者简介：熊晓莉，博士，讲师，Email：x_shanley@sina.com。

 

［1］CHEN SHAOFAN. Buckling of T-strut subject to compressive force on its shear center［J］. Journal of Constructional Steel Research，2007, 63：332-336.

［2］陈绍蕃. 剖分T型钢压杆的屈曲性能和应用［J］. 建筑钢结构进展，2005，7（4）：1-5.

［3］TIMOSHENKO S P, GERE J M. Theory of elastic stability［M］. New York：McGraw-Hill，1961.

［4］CHEN W F, ATSUTA T. Theory of Beam-Columns［M］. New York：McGraw-Hill，1977.

［5］GB 50017—2003钢结构设计规范［S］. 北京：中国计划出版社，2003.

 ［6］彭晓彤，陈绍蕃，顾强. 剖分T型钢压杆的弯扭屈曲试验研究 ［J］. 建筑结构学报，2004，25(2)：44-48.