刘汉勇1，宋玉普1，李龙2（1 大连理工大学海岸和近海工程国家重点实验室，大连 116024；2 山东省建筑科学研究院，济南 250031）

［摘要］在MTS电液伺服疲劳试验机上进行了直径70mm的新型不锈钢吊杆在拉伸荷载作用下的疲劳试验，疲劳荷载上限为700kN，下限为430kN，在经历了1 546 609次循环后，吊杆从下部螺纹连接公接头第一承载齿的根部突然断裂。采用ANSYS软件，建立了新型不锈钢吊杆螺纹连接的二维轴对称模型，分析了各螺纹承载齿承担的荷载以及螺纹齿根在拉伸荷载作用下的应力集中系数，分析结果表明，应力集中系数最大值出现在螺纹连接公接头第一承载齿的根部。同时还分析了螺纹连接的最大应力，结果表明，螺纹连接头最大应力的位置与吊杆断裂面疲劳裂纹源的位置相吻合。

［关键词］不锈钢吊杆；螺纹连接；疲劳试验；数值分析

中图分类号：U441+.4文献标识码：A文章编号：1002-848X(2012)04-0162-04

Fatigue test of arch bridge stainless steel suspender and stress analysis of threaded connection

Liu Hanyong1, Song Yupu1, Li Long2(1 State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology, Dalian 116024, China; 2 Shandong Provincial Academy of Building Research, Jinan 250031, China)

Abstract:A fatigue test and a finite element analysis on an arch bridge stainless steel suspender with threaded connections were carried out. A suspender which had a diameter of 70mm was tested under axial tensile loads range from 430kN to 700kN. The suspender suddenly failed from the thread root of the first loaded tooth in the pin after 1 546 609 cycles. A two-dimensional axisymmetric modeling ignoring the helix angle of thread was established with finite element software ANSYS to perform a stress analysis of the threaded connection. The stress concentration factors (SCF) at the root of the teeth of pin were investigated under applied external loading. The conclusive results had been drawn from the analysis including load distribution on the threads and location and value of maximum SCF in the pin. The location and value of maximum stress were given. The results show that the location of fatigue crack source on the fracture surface is consistent with the location of maximum stress.

Keywords:stainless steel suspender; threaded connection; fatigue test; numerical analysis

*国家高技术研究发展计划（863计划）（2007AA11Z133）。

作者简介：刘汉勇，博士研究生，Email: structliu@yahoo.com.cn。

参考文献

［1］ YOUNG B, LIU Y. Experimental investigation of cold-formed stainless steel columns ［J］. Journal of Structural Engineering, 2003, 129(2): 169-176

［2］ GARDNER L, NETHERCOT D A. Experiments on stain-less steel hollow section members—part 2: member behaviour of columns and beams ［J］. Journal of Constructional Steel Research, 2004, 60 (9): 1319-1332

［3］ 苏庆田, 沈祖炎, 张其林，等. 不锈钢强度设计值取值的试验和理论依据［J］. 建筑结构学报, 2003, 24(1): 80-83

［4］ YOUNG B, LUI W M. Behavior of cold-formed high strength stainless steel sections ［J］. Journal of Structural Engineering, 2005, 131(11): 1738-1745

［5］ RASMUSSEN K J R. Full-range stress-strain curves for stainless steel alloys ［J］. Journal of Constructional Steel Research, 2003, 59（1）: 47-61

［6］ YU W W. Cold-formed steel design ［M］. 3rd ed. New York: Wiley, 2000

［7］ SEI/ASCE-8-02 ASCE specification for the design of cold-formed stainless steel structural members ［S］. Reston: American Society of Civil Engineers, 2002

［8］ BS EN 1993-1-4  Design of steel structures-part 1-4: general rules-supplementary rules for stainless steels ［S］. Brussels: European Committee for Standardization, 2006

［9］ AS/NZS 4673: 2001 Cold-formed stainless steel structures ［S］. Sydney: Australian/New Zealand Standard, 2001

［10］ FESSLER H, JOBSON P K. Stresses in a bottoming stud assembly with chamfers at the ends of the threads ［J］. Journal of Strain Analysis, 1983, 18(1): 15-22

［11］ KENNY B, PATTERSON E A. Load and stress distribution in screw threads ［J］. Experimental Mechanics, 1985, 25(3): 208-213

［12］ MACDONALD K A, DEANS W F. Stress analysis of drill string threaded connection using the finite element method ［J］. Engineering Failure Analysis, 1995, 2(1): 1-30

［13］ TAFRESHI A. SIF evaluation and stress analysis of drillstring threaded joints ［J］. International Journal of Pressure Vessels and Piping, 1999, 76(2): 91-103

［14］ SHAHANI A R, SHARIFI S M H. Contact stress analysis and calculation of stress concentration factors at the tool joint of a drill pipe ［J］. Materials and Design, 2009，30（9）: 3615-3621

［15］ RAMBERG W, OSGOOD W R. Description of stess-strain curves by three parameters ［R］.  Washington D C，1943

［16］ ABDELLA K. Inversion of a full-range stress-strain relation for stainless steel alloys ［J］. International Journal of Non-Linear Mechanics, 2006, 41（3）: 456-463

［17］ ABDELLA K. An explicit stress formulation for stainless steel applicable in tension and compression ［J］. Journal of Constructional Steel Research, 2007, 63（3）: 326-331