（1 西安建筑科技大学土木工程学院， 西安 710055； 2 陕西省建筑科学研究院， 西安 710082）

［摘要］在钢结构设计中应考虑轴心受拉平板不完全连接时产生的剪力滞后效应，国外规范对此做出了折减截面面积的相关规定，但是折减程度偏大，直接引入我国规范使用稍显不经济。通过有限元软件ABAQUS对国外相关试验进行了模拟，验证了模型的正确性，并使用该模型分析了焊缝长度、板宽度等参数对剪力滞后的影响，分析了考虑剪力滞后效应和未考虑剪力滞后效应时关键截面应力分布情况。通过通用屈服弯矩法对杆件的恢复力曲线进行处理，得到了杆件屈服荷载，确定了面积折减系数。将有限元计算得到的折减系数和国外规范及征求意见稿进行对比和分析，最后给出了该折减系数的取值建议。

［关键词］轴心受拉; 剪力滞后; 净截面; 折减系数

中图分类号：TU202，TU391      文献标识码：A      文章编号：1002-848X(2014)09-0043-05

Analysis on shear lag effect of axial tension plate with side fillet welding connection

Luo Zheng1, Lei Siwei1, Zhang Fengliang2

 (1 School of Civil Engineering, Xi’an University of Architecture and Technology, Xi’an 710055, China; 2 Shaanxi Institute of Architecture Science, Xi’an 710082, China)

Abstract: In the steel structure design, the shear lag effect should be considered in axial tension plate with incomplete connection. Foreign codes have made relevant provision which is about reduction cross section area, but reduction degree is too large. It is slightly not economic if the foreign code is directly introduced into Chinese code. Through the finite element software ABAQUS, foreign related test was simulated to verify the accuracy of model, and the model was used to analyze the effect of weld length, plate width, etc. on the shear lag. The critical cross section stress distribution was analyzed by considering and not considering the shear lag effect. Through the general yield bending moment method, restoring force curves of member processing were analyzed to obtain the yield load. Then area reduction factor was determined. Compared FEM result with foreign code and Chinese code draft，the suggested values of the reduction coefficients were given.

Keywords: axial tension; shear lag; net area; reduction coefficient

作者简介：罗峥，硕士研究生，Email：luozheng0130@gmail.com。

参考文献

［1］陈绍蕃，顾强.钢结构［M］.北京：中国建筑工业出版社，2003.

［2］陈绍蕃.钢结构设计原理［M］.北京：科学出版社，2003.

［3］刘菁菁，郝际平，钟炜辉.国内外钢结构设计规范关于剪切滞后的比较［J］.建筑结构，2011,41（S1）：943-946.

［4］GB 50017—2003 钢结构设计规范［S］.北京：中国计划出版社，2003.

［5］ANSI/AISC 360-05 Specification for structural steel buildings［S］.Chicago：American Institute of Steel Construction Inc. 2005.

［6］CAN/CSA-S16-01 Limit states design of steel structures［S］.Toronto：Canadian Standards Association(CSA), 2001.

［7］American Bureau of Welding. Report of structure steel welding committee［R］. New York: American Welding Society, 1931.

［8］EASTERLING W S, GONZALEZ GIROUX L.Shear lag effects in steel tension members［J］.AISC Engineering Journal,1993,30(3)：77-89.

［9］ABI-SAAD G，BAUER D. Analytical approach for shear lag in welded tension members［J］.Canadian Journal of Civil Engineering，2006，33（4）：384-394.

［10］刘菁菁.轴心受拉构件部分连接时的剪力滞后影响分析［D］.西安：西安建筑科技大学，2011.

［11］姚谦峰，陈平.土木工程结构试验［M］.北京：中国建筑工业出版社，2001.